Clover Leaf Mob Drop Farm

An elevated clover-shaped mob spawner featuring long glass drop shafts and a ground-level handling area.

Clover Leaf Mob Drop Farm
Download schematicView in 3DFree .schematic file on 9Minecraft Schematics · works with WorldEdit and Litematica

What you are building

The Clover Leaf Mob Drop Farm is an elevated hostile mob spawner that funnels spawns into drop chutes leading to a ground-level processing station. Featuring an iconic four-lobed clover footprint, the elevated spawning room keeps mob spawns clustered directly above long vertical drop shafts to weaken or separate them upon landing.

Because of its elevated platform, this structure is best constructed high in the sky or over ocean terrain to reduce underground cave lighting requirements. Note that this is a classic legacy design created before Minecraft 1.13; mob pathfinding and spawning rules have shifted significantly since then, so you should test the layout in a creative world before assembling it in survival.

Legacy design. The file is from an old version and this kind of farm depends on mechanics that changed in later updates. Treat it as a layout reference, not a guaranteed working farm.

This is a legacy design from an early Java version; water mechanics and mob AI differ in modern editions, so test water flow and mob drop behavior in a creative test world first.

Build your lower waiting platform at least 24 blocks below the spawning floor so mobs are able to spawn naturally while you wait at the base.

Materials 4,430 blocks · 22 types

  • Water1,59624 stacks + 60
  • White Wool88713 stacks + 55
  • Green Wool80712 stacks + 39
  • Light Gray Wool4967 stacks + 48
  • Glass2163 stacks + 24
  • Dirt1312 stacks + 3
  • Red Wool661 stack + 2
  • Redstone Wire63
  • Stone37
  • Cobblestone25
  • Redstone Lamp20
  • Oak Pressure Plate20
  • Sand18
  • Torch16
  • Repeater10
  • Stone Brick Stairs8
  • Piston6
  • Lever2
  • Oak Fence2
  • Chest2
  • Crafting Table1
  • Oak Wall Sign1

How it works

Hostile mobs spawn within the dark chambers of the upper clover-leaf floor, where designated water streams push them toward central collection openings. Mobs fall through vertical glass shafts down to the ground station, taking heavy fall damage along the way.

At the base, redstone lines, pistons, and pressure plates regulate mob containment and positioning. When arranged properly, players can finish off weakened mobs manually or position skeletons to strike creepers to obtain music discs.

How to use it

To operate the grinder, toggle the control lever at the lower station and stand on the designated observation platform to let mobs spawn in the elevated chamber above. Once mobs descend through the glass drop columns, interact with the piston controls to hold them in place or dispatch them at the bottom to collect their drops into nearby chests.

Lay the Foundation and Control Station

Layers 1–5 of 34

Begin by mapping out the ground footprint using dirt, stone, and colored wool walkways. Position your primary utility blocks, including the crafting table, chests, and initial glass partition walls where the drop chutes will land.

Set down the red wool wiring track with redstone wire and repeaters leading to the piston containment chambers at the base.

Clover Leaf Mob Drop Farm - step 1: Lay the Foundation and Control Station

Begin Raising the Vertical Chutes

Layers 6–14 of 34

Start extending the vertical drop columns upward using glass blocks. Assemble the lower access walkways with green wool and secure torches around the control perimeter to prevent stray spawns around the workstation.

Clover Leaf Mob Drop Farm - step 2: Begin Raising the Vertical Chutes

Extend Drop Columns to Full Height

Layers 15–24 of 34

Continue stacking the four vertical glass chute shafts up toward layer 24. Ensure the interior drop channels remain completely open so falling mobs travel straight down without snagging on block edges.

Clover Leaf Mob Drop Farm - step 3: Extend Drop Columns to Full Height

Build the Spawning Floor and Roof

Layers 25–34 of 34

Cap the drop chutes with light gray wool flooring and expand outwards into the wide four-lobed clover platform using green and white wool. Shape the interior water canals to funnel mobs directly into the chute openings.

Seal the structure with an opaque ceiling, install redstone lamps with pressure plates or wiring along the upper surface, and verify the interior spawning zones remain pitch black.

Clover Leaf Mob Drop Farm - step 4: Build the Spawning Floor and Roof

Finishing touches

Before sealing the roof completely, verify that water sources flow precisely to the lip of each drop hole without spilling down the glass shafts. Light up the entire exterior roof and surrounding ground area with torches to ensure mobs only spawn inside the dark upper clover chamber.

Frequently Asked Questions

Why are the drop tubes made of glass?

Glass allows you to monitor descending mobs without giving them solid surfaces to glitch into, while also keeping your player view unobstructed around the drop station.

Can I replace the wool blocks with solid stone?

Yes, any solid spawnable block such as cobblestone or stone bricks can replace the wool without disrupting the internal spawning mechanics.

#mob grinder#legacy#drop tower#music discs#redstone

Download schematicView in 3DFree .schematic file on 9Minecraft Schematics · works with WorldEdit and Litematica

You May Also Like